When Removing Screws While Working on a Laptop

You can also make use of super glue or epoxy to attach something to the screw head. Epoxy will probably make a stronger bond but it can take quite more time to be set. We’ll need to figure out an approach to fill in the gaps so that the screwdriver will be able to grip the surface. Take the power supply unit off by disconnecting the remaining connectors, and then unplugging the the frame. You’ll need an incredibly small Phillips-head screwdriver, and, depending on the manufacturer of the components, perhaps using a flathead screwdriver. The computer’s case is very sharp, and you may need gloves as well.

In the majority of cases, when you’re in the process of disassembly, you’ll arrive near the point that you need to remove the lower covers from the upper case. Be sure that all screws connecting the two pieces together are taken out. Remove all the wires from the motherboard. Finally, take it off it by turning each screw just a tiny bit before moving around over and again to loosen the screws correctly. This will prevent any possible distortion of the motherboard by gradually releasing the tension from it. The memory modules can be removed by pressing the clips at both ends of the module.

If you’re rebuilding your computer, make sure you record the location you took components out of and the order in which they were removed and what cables connect to each component. You can snap pictures prior to every removal, or record it in a notebook.

Rebuilding and disassembling laptops will allow you to replace components or clean your system or even remove the internal components of your laptop. The connector on the following image is similar to the one that was previously shown. When you have a close inspection of the cable, you will notice two extensions on the sides . After unlocking the connector , you’ll be required to raise the cable just a bit in order to pull it out. There are numerous kinds of connectors in laptops of every type.

When you upgrade a laptop, it is recommended to make sure that the components are of identical to the brand of the laptop, or choose only the recommended parts. It is possible to purchase left handed drill bits, which , as they are named are made to spin counterclockwise, which is in the opposite direction to standard drill bits. It is a great moment to clean any dust, lint or hairs from the fans if you’re thinking of recycling the same ones. The cable will be blocked inside and you have to remove it by pulling the cable away.

Don’t use the gold connectors on the chips if you’re using the modules. If you’re not recycling the RAM, you should find out what it is that it can be used for other purposes.

Rubber Glove

Make sure the screws are in their respective component and screw them into the holes on the component or the frame or by tapering them in the proper location. When assembling your laptop, complete every step in reverse order. Make sure that the connectors are securely seated and cables aren’t bent or stretched out, or all screws fit back into the correct holes. It’s usually recommended to tighten screws in a series on a piece to avoid breaking the component. For the ribbon cable for keyboards the lighter end is pulled up to stop twisting in the cable.

Removing Screws

Remove the screws that join your display with the hinge. They may be located in the rear of the display or on the inside which is where there was a keyboard. Take out any other cables that are in the area below the keyboard. If the cable is fitted with tiny plastic plugs and it pulls it out. This type of connector is typically used to connect fans and speakers.

Step 7

This guide outlines the most commonly used ways computers are assembled but the computers and the manufacturers may differ. If you’re unable to access a specific component even though it’s mentioned in the guide, just skip to the steps to take out other components until you reach the primary component. Connectors for power on the board are used to power cards that consume a lot of watts. In this instance it is possible to achieve the same result simply by placing the screwdriver into an ordinary kitchen glove that is made of rubber! It is possible to place the head of the screwdriver in some of your glove’s fingers, and use the glove to gain additional purchasing power similarly to by putting a rubber band around the end. The design of the screwdriver present, however it’s been made larger by using the band.

If the component isn’t moving, you should check the other attachments holding the device in place. The small, gold-tipped cover close to the wireless card is the antenna for wireless.

Disconnecting Internal Cables

If you drop a screw into the motherboard, or touch to it using a screwdriver, it could damage the motherboard, rendering it irreparable. A screw that is stripped doesn’t have any grip whatsoever it’s just too little material inside the screw head to allow a screwdriver to hold on. If you’re planning to rebuild your laptop, you must keep track of where each component goes and which cables are attached to it, and the location where the cable’s slack is kept. Make a photo of every step in order to make it easier to assemble your notebook at conclusion of the procedure. Make sure you keep track on the screw and the locations they go because various sizes and types of screws may be used for the same piece of equipment. To avoid any confusion Re-insert screws in the holes where they were originally or put the screws close to the proper hole on the part. Which of these statements concerning working with laptop computer is correct?

If the laptop isn’t functioning in a proper way after the assembly (no audio or video, no wireless connectivity, etc. …) make sure you check the internal cable connections first. It is likely that you didn’t connect the cables, or you didn’t connect them correctly. If the cable gets damaged your laptop’s wireless connectivity. It isn’t easy to replace antenna cables since they are inside an LCD panel. The connectors below are typically found on video cables for display.